- #CAL.INI SD C4 HOW TO#
- #CAL.INI SD C4 INSTALL#
- #CAL.INI SD C4 DRIVERS#
- #CAL.INI SD C4 UPDATE#
- #CAL.INI SD C4 SOFTWARE#
How to Set up PCMTuner for GM SPS2 Online Programming?.Repair Carprog A1 Adapter for CAN BUS cummunicationīMW INPA 6.4.3, 5.0.6,5.0.2 Free Download
#CAL.INI SD C4 SOFTWARE#
How to use BMW INPA software and cable K+DCAN
#CAL.INI SD C4 INSTALL#
How to install TIS2000 for GM Tech 2 scanner
#CAL.INI SD C4 DRIVERS#
Install BMW INPA on WinXP Win7 Win8 Win10įree Download BMW E-sys V3.22.5 v3.2.61 v3.2.71įree ECM Titanium 1.61 with 26000 drivers How to Install Toyota TIS Techstream 14.10.028 This must be done in conjunction with the actual car ignition. Note: when ISTA/P asks for ignition ON/OFF during programming use the K15 controls located in the notification area of the taskbar (or the Hotkeys).
Then wait for emulator running notifications to appear Select Internet Protocol Version 4 (TCP/IPv4)>propertiesĬ- Manually change IP to 169.254.0.8 and subnet mask to 255.255.0.0>ok>closeĤ Disable your antivirus, firewall and turn off WIFIĥ Plug in your K+DCAN cable to car and PC.Ħ Click on the “K+DCAN ICOM emulator button”. Note: if the network config tool does not work correctly, use the procedure below (mainly applies to non-English systems)Ī- Rename the newly created adapter to USB and disableī- Right click on USB->properties. Then check in network connections that the USB network connection has appeared Reboot your computerģ Run K+DCAN network configuration tool from the loader menu (may take up to 30 seconds to complete) Part 3: BMW INPA K+DCAN USB cable configuration manualĢ Install your K+DCAN cable and set COM port to COM9. Then wait for emulator running notifications to appearħ On loader main screen, click on the relevant brand button for your car. ZGW search will openĦ Enter your car’s ZGW IP and click on “Continue”. Turn on ignition and wait for a minute or two.ĥ Click on the “ENET ICOM emulator button”. Part 2: BMW ENET cable configuration manualĤ Connect ENET cable to car and PC. Wait for a minute or twoĥ On loader main screen, click on the relevant brand button for your car/motorcycle. Part 3: K+DCAN USB cable configuration manualġ Install patched Ediabas 7.3 from the loader menu and reboot your computerĢ Set up your Ethernet adapter as shown belowģ Disable your antivirus, firewall and turn off WIFIĤ Connect ICOM to car and PC. (or just lucky me.How to configure ICOM, ENET, K+DCAN cable? What’s the difference? Here, BMW ICOM cable config manual:
#CAL.INI SD C4 UPDATE#
Then give a try, the error should be gone, and my C4 (bought in 2011) does not need any firmware update for Xentry 2014.01, so I give a wild guess that firmware update for MUX is optional. When you see this issue XXXX.XXXX.9901 (check last 4 digits) and unable to connect your vehicle, please remove (or rename) SD connect firmware connect files under :Ĭ:\Program files\SDconnect Toolkit\update_automaticĬ:\Program files\SDconnect Toolkit\update_manualĬ:\Program files\SDconnect Toolkit\update_update special Just want to share my troubleshooting experience on Xentry 2014.01. Important: When trying new Xentry version, please make sure apply blacklist fix to Xentry and Das, otherwise it gonna block your MUX “Solution for XXXX.XXXX.9901 error in Xentry 01.2014 “you must change plattfortm_w to plattform_D2” Start Xentry/das and it worked straight away. re-delete or Rename update folders after running SDNC setupĩ. No options, but it went automaticaly to instalation :SĦ. The “repair” option wasnt displayed, but it went straight into instalation. start laptop (Dell d630 laptop will be better)Ĥ.
The indtruction above means that users shouldġ. it is VERY important to REBOOT after deleting the update folders!!! let it do its thing and then go back and delete/rename the update folders in C:\program files\SDconnect toolkit then REBOOT when its done… that should get you up and running. it will start up and ask what you want to do, select repair. then perform a repair of your SDNetControl by pressing Start\Programs\Service\Setup SDNetControl. “Delete the 3 “update” folders in C:\program files\SDconnect toolkit (or rename them). Software version: Xentry Open Shell 092015 So please be responsible for what you will do later. Some sulutions found on forums are here, but there may be some risks if you try the solutions below. Xentry and DAS work fine, but everytime the Star diagnostic Mux is connected with the car, the error below will appear: Here are some useful tips some users tried suceessfully for Star diagnosis MB STAR C3/ SDConnect C4 Connection Error: (1.2)-2.503.9901.
0 kommentar(er)
